Control PanelSource-checked
ID3000
Modular addressable fire alarm control panel family documented in NOTIFIER system design resources.
Notifier by Honeywell
Official sources checkedFire detection control equipment documented by Honeywell Notifier product resources.
- Reviewed products
- 3
- Panel records
- 3
- Verified faults
- 98
- Reviewed parts
- 0
Official resource links last checked August 4, 2026.
Manufacturer overview
Documented engineering coverage
Incognito records the manufacturer identity, official resources and supported product families shown on this page. Coverage confirms catalogue evidence only. It does not imply manufacturer approval, product compatibility or access to restricted support.
- Product categories
- Fire detection
- Typical engineering use
- Addressable control panels, networked systems, official specifications
- Known names
- Notifier by Honeywell, Notifier, Notifier Fire Systems
Common engineer searches
Continue in engineering search
Products supported by Incognito
Documented product families
Lifecycle labels are shown only when a current official page or manufacturer lifecycle notice supports the classification. All other product names remain unclassified.
Current products
PearlView status source
ID3000View status source
Also found as ID 3000
Source reviewed technical data
Structured product records
These records expose only supported specifications and retain missing values rather than filling them by assumption.
Io ModuleSource-checked
M701E Single Output Module
Addressable single-output module providing a monitored circuit for polarised loads or an unsupervised switched output, with selectable loop isolation.
Control PanelSource-checked
Pearl
Addressable fire detection control system documented in the official NOTIFIER specification library.
Direct from the manufacturer
Official resources
Each record includes an original Incognito summary before the external link. Incognito does not host or mirror the linked material.
Official websiteOfficialLink checked
NOTIFIER by Honeywell (products and resources)
Published by Honeywell
Incognito summary
Use this official Honeywell resource as a primary route to website information. Confirm that any document or download matches the installed product, revision and local project requirements before relying on it.
- Useful for
- starting with the manufacturer's current product and service information
- Intended audience
- engineers, specifiers, maintainers and system owners
- Product range covered
- Notifier by Honeywell product and support resources
- Companion knowledge
- ArticleFault recordsFAQsTroubleshooting
Checked Nov 4, 2026Open official resource
Documentation, videos and downloads remain the property of their respective manufacturers.
Incognito technical guidance
Related articles and guides
Source reviewed records
Related fault records
ID50 / ID60 • 6 MONTHS TO CELL LIFE EXPIRYID50/60: 6 MONTHS TO CELL LIFE EXPIRYMessage shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: The Carbon Monoxide (CO) cell of a SMART 4 multi-criteria sensor has 6 months to end of life. Action listed in the manual: Record in site log book.ID3000 • Aux. Output X FaultAux. Output X FaultParameterised message covering auxiliary outputs 1 and 2 (X = 1 or 2), as printed in the source ('Aux. Output 1 Fault'; 'Aux. Output 2 Fault'). Indicates a failure of the auxiliary drive circuits, not the attached cables. Action: If the fault is on either circuit, change the Base PCB (Kit PN: 020-568).ID50 / ID60 • AUXILIARY SUPPLY FAULTID50/60: AUXILIARY SUPPLY FAULTMessage shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: A fault with the auxiliary supply has been detected. Action listed in the manual: Check the auxiliary voltage and any associated wiring.ID50 / ID60 • BAD REPLY FROM DEVICEID50/60: BAD REPLY FROM DEVICEMessage shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: Corrupted communication has been detected between the panel and a loop device. Action listed in the manual: Replace loop device. If problems persist the base board will need to be replaced.ID50 / ID60 • BATTERY CHARGER FAILUREID50/60: BATTERY CHARGER FAILUREMessage shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: The integral battery charger has failed and the batteries are no longer being charged. Action listed in the manual: Replace base board.ID50 / ID60 • BATTERY DISCHARGEDID50/60: BATTERY DISCHARGEDMessage shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: The output voltage of the batteries has fallen below the minimum required for correct panel operation. Action listed in the manual: Check the condition of the batteries.
Engineer questions
Related FAQs
No FAQ for this manufacturer has completed source review. Search remains available without presenting unreviewed answers as verified guidance.
Technical guidance boundary
Use the exact current manufacturer document for the installed model and revision. Confirm the site configuration, cause and effect, fire strategy, applicable standards and safe isolation procedure before taking action. Incognito does not claim manufacturer endorsement or guarantee a diagnosis.
One connected engineering library
The live technical database contains 30 supported manufacturers, 96 panel records and 186 reviewed product records.
Other manufacturer hubs
AdvancedApollo Fire DetectorsASL Fire & SecurityBaldwin BoxallBoschC-TECEatonEMSESSER by HoneywellFikeFireClassGent by HoneywellGlobal Fire EquipmentHaes SystemsHochiki EuropeHoneywell SecurityKentec ElectronicsMorley-IASNittan EuropePaxtonProtecPyronixSiemensSimplexTexecomXtralisZeta Alarm SystemsZiton