Control PanelSource-checked
CIE-A-200 Addressable Fire Alarm Control Panel
Single-loop addressable fire alarm control panel for up to 200 Fike addressable devices; explicitly superseded by CIE-A-400.
Fike
Official sources checkedFire detection control equipment represented from Fike's official product information.
- Reviewed products
- 3
- Panel records
- 6
- Verified faults
- 39
- Reviewed parts
- 0
Official resource links last checked July 19, 2026.
Manufacturer overview
Documented engineering coverage
Incognito records the manufacturer identity, official resources and supported product families shown on this page. Coverage confirms catalogue evidence only. It does not imply manufacturer approval, product compatibility or access to restricted support.
- Product categories
- Fire detection
- Typical engineering use
- Fire detection, control equipment, manufacturer product documentation
- Known names
- Fike, Fike Safety Technology
Common engineer searches
Continue in engineering search
Products supported by Incognito
Documented product families
Lifecycle labels are shown only when a current official page or manufacturer lifecycle notice supports the classification. All other product names remain unclassified.
Lifecycle not classified
Cheetah XiNo lifecycle claim made
DuonetNo lifecycle claim made
TwinflexNo lifecycle claim made
Source reviewed technical data
Structured product records
These records expose only supported specifications and retain missing values rather than filling them by assumption.
Control PanelSource-checked
CIE-A-400 1-2 Loop Addressable Fire Alarm Control Panel
One-loop addressable fire alarm control panel expandable to two loops using the documented 540-0003 loop card.
Control PanelSource-checked
TWINFLEXpro2 4 Zone Control Panel
Four-zone intelligent two-wire analogue non-addressable fire alarm control panel.
Direct from the manufacturer
Official resources
Each record includes an original Incognito summary before the external link. Incognito does not host or mirror the linked material.
Product catalogueOfficialLink checked
Fire alarm control panels
Published by Fike
Incognito summary
Use this official Fike resource as a primary route to products information. Confirm that any document or download matches the installed product, revision and local project requirements before relying on it.
- Useful for
- checking current product information, variants and manufacturer supplied downloads
- Intended audience
- design, installation, commissioning and maintenance engineers
- Product range covered
- Fike product and support resources
- Companion knowledge
- ArticleFault recordsFAQsTroubleshooting
Checked Sep 30, 2026Open official resource
Documentation, videos and downloads remain the property of their respective manufacturers.
Incognito technical guidance
Related articles and guides
Source reviewed records
Related fault records
Fike Twinflex10 sourced fault recordsCIE-A-4005 sourced fault recordsCIE-A-20010 sourced fault recordsQuadnet14 sourced fault records
CIE-A-200 • Addressable circuit: -ve open circuitCIE-A-200: Addressable circuit: -ve open circuitPer the manual, if the system faces a loop -ve open circuit during initialisation, initialisation does not fail at that point but continues to the end of the loop and all devices are operational (as long as no other faults exist). A message of Addressable circuit: -ve open circuit is displayed, but the panel cannot detect where the open circuit is. To locate it, stop the loop, disconnect loop end 2, wait at least 3 minutes and reinitialise: initialisation then fails at that point and Loop not complete is displayed. The loop must be reinitialised to clear the fault, always waiting at least 3 minutes between stopping a loop and reinitialising.Quadnet • Addressable circuit: -ve open circuitQuadnet: Addressable circuit: -ve open circuitPer the manual, if the system faces a loop -ve open circuit during initialisation, initialisation continues to the end of the loop and all devices are operational (as long as no other faults exist). A message of Addressable circuit: -ve open circuit is displayed, but the panel cannot detect where it is. To locate it, stop the loop, disconnect loop end 2, wait at least 3 minutes and reinitialise: initialisation then fails at that point and Loop not complete is displayed. The loop must be reinitialised to clear the fault.CIE-A-200 • Device faults during initialisationCIE-A-200: Device faults during initialisationPer the manual, if the system detects a device fault or fire activation during initialisation, initialisation does not fail at that point. Beyond certain limits initialisation will fail and the various fault or fire activations are displayed. Deal with the events before reinitialising: first investigate and rectify fire activations (from unreset call points to contaminated multipoint detectors), then fault conditions (from Input open circuit to a multipoint detector with its optical chamber loose, indicating signal low). Devices or chambers should be removed or replaced only with the loop stopped.Quadnet • Device Quantity MismatchQuadnet: Device Quantity MismatchPer the manual, after initialising the loop, if the number of devices initialised does not match the number programmed, a DEVICE QUANTITY MISMATCH screen appears showing the number found and programmed. A mismatch occurs if devices have been removed or added and the changes have not been updated in the OSP and downloaded into the panel, or if the loop was initialised too quickly after it was stopped (stop the loop and wait at least 5 minutes before reinitialising). On a new panel a mismatch is likely, because it will have been tested in the factory with various configurations.CIE-A-200 • Device Quantity MismatchCIE-A-200: Device Quantity MismatchPer the manual, a device mismatch occurs if a device or devices have been physically removed from or added to the system and the changes have not been updated in the OSP and downloaded into the panel; the panel expects to find the original number of devices downloaded to it. Check the site information for changes and compare with the OSP file. Another cause is initialising the loop too quickly after it was stopped: if a device has not powered down completely it may be missed and cause a mismatch. Stop the loop and wait at least 5 minutes before reinitialising.CIE-A-400 • DEVICE QUANTITY MISMATCHDevice quantity mismatchThe number of devices found during CIE-A-400 loop initialisation does not match the number programmed in the approved OSP configuration.
Engineer questions
Related FAQs
No FAQ for this manufacturer has completed source review. Search remains available without presenting unreviewed answers as verified guidance.
Technical guidance boundary
Use the exact current manufacturer document for the installed model and revision. Confirm the site configuration, cause and effect, fire strategy, applicable standards and safe isolation procedure before taking action. Incognito does not claim manufacturer endorsement or guarantee a diagnosis.
One connected engineering library
The live technical database contains 30 supported manufacturers, 96 panel records and 184 reviewed product records.
Other manufacturer hubs
AdvancedApollo Fire DetectorsASL Fire & SecurityBaldwin BoxallBoschC-TECEatonEMSESSER by HoneywellFireClassGent by HoneywellGlobal Fire EquipmentHaes SystemsHochiki EuropeHoneywell SecurityKentec ElectronicsMorley-IASNittan EuropeNotifier by HoneywellPaxtonProtecPyronixSiemensSimplexTexecomXtralisZeta Alarm SystemsZiton