Fault records by panel

The FlexES Control local essernet receive buffer has reached 100 percent because one or more network participants have not acknowledged telegrams despite retries. FAQ 1001 treats codes 98 and 99 as one combined…

These faults indicate the occurrence of one or more of: a. Faulty or disconnected batteries (if discharged batteries are connected, they may remain in Battery Low Voltage for a period until the voltage is raised by the…

These faults indicate the occurrence of one or more of: a. Faulty or disconnected batteries (if discharged batteries are connected, they may remain in Battery Low Voltage for a period until the voltage is raised by the…

Displayed only if the NGM PCB stopped working after a period of working correctly. If this is not quickly followed by the Network startup fault message, the NGM PCB has successfully re-started. Action (shared with…

These faults indicate the occurrence of one or more of: a. Faulty or disconnected batteries (if discharged batteries are connected, they may remain in Battery Low Voltage for a period until the voltage is raised by the…

Message shown on the Vigilon panel. Meaning per the manual: the integral printer is not 'seen' by the control panel. Indications listed: Fault. Action listed in the manual: check the connections to the printer and check…

Message shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: Some form of corruption has been detected within the configuration settings. This can occur following a software upgrade if the memory…

Message shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: The control panel has been reset either by a complete removal of power to the panel, pressing the reset button on the base board or…

Message shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: A wiring fault has been detected to earth. Action listed in the manual: The fault can be narrowed down by systematically disconnecting…

Message shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: Loop isolator is open circuit either by command from the panel or because of a loop fault. Action listed in the manual: Check if device…

After the detector loop is switched on, Störungscode 24 means that an automatic detector cannot correctly control its base board. A base relay PCB may not be reliably controlled, so required event control can fail.…

An IQ8Wireless participant has a radio communication fault. FAQ 1010 directs the engineer to inspect preceding Batt < 30 and Batt < 7 indications as evidence of depleted batteries; those indications are references only…

After the detector loop is switched on, Störungscode 24 means that an automatic detector cannot correctly control its base board. A base relay PCB may not be reliably controlled, so required event control can fail.…

An IQ8Wireless participant has a radio communication fault. FAQ 1010 directs the engineer to inspect preceding Batt < 30 and Batt < 7 indications as evidence of depleted batteries; those indications are references only…

After the detector loop is switched on, Störungscode 24 means that an automatic detector cannot correctly control its base board. A base relay PCB may not be reliably controlled, so required event control can fail.…

An IQ8Wireless participant has a radio communication fault. FAQ 1010 directs the engineer to inspect preceding Batt < 30 and Batt < 7 indications as evidence of depleted batteries; those indications are references only…

Parameterised message covering auxiliary outputs 1 and 2 (X = 1 or 2), as printed in the source ('Aux. Output 1 Fault'; 'Aux. Output 2 Fault'). Indicates a failure of the auxiliary drive circuits, not the attached…

This indicates that a device has been installed without setting a valid address, i.e. left at factory default of '00'. No separate remedial action is stated beyond this cause in the source.

These four fault messages are grouped in the source as all indicating a loop PCB failure. Action: Replace the loop PCB (PN: 020-588).

The earth fault monitor detects the presence of an earth on the positive or negative sides of the system. Should this condition occur, disconnect the field circuit wiring one cable at a time and view the LED at the top…

Communications fault between the CPU and the display. Action: Change the CPU PCB assembly (PN: 020-569) and/or the Display PCB/Membrane Keypad (PN: 020-571-XXX).

No separate cause description is given for this message beyond its name. Action: Change the Base PCB (PN: 020-568) or Extension Chassis with Display Module Kit (PN: 020-559-XXX).

This fault message can only appear when ID3000 panels are networked with earlier compatible panels; it is not applicable to the 'local' ID3000 Series panel. Where it is applicable, an Extension Chassis with Display…

Missing PCB — the panel is configured for network but no RS485 PCB is present. Fit Isolated RS485 Module Kit (PN: 020-479) or change configuration.

Missing PCB — the panel is configured for 3rd-party protocol but no RS232 PCB is present (does not apply to other modes of the port). Fit Isolated RS232 Module Kit (PN: 020-478) or change configuration.

An attempt has been made to remove one of these items while the panel is powered up. Remove power before proceeding.

Two nodes have the same node id. Action: Change the id number of one of the duplicate nodes (use the diagnostic tool).

Most likely to occur in the event of a broken network connection, i.e. short or open circuit cable or broken optical fibre. May also indicate an NGM PCB hardware fault. There would normally be two fault messages, one at…

The source states this fault has the same cause and remedy as 'ID2net: Channel 1 Link Fault' — see that entry.

This message indicates an NGM PCB failure. Action: Replace the NGM PCB. Note: the source states other fault conditions may occur in exceptional circumstances, in which case contact your supplier for guidance.