Fault records by panel

The yellow Fire Protection Fault/Disabled/Test LED indicates a fire protection fault, disablement, or test. A flashing LED indicates a fault; a steady LED indicates a disablement or a test. From the ZP2 Series…

The yellow Supply Fault LED indicates a power supply fault. A steady LED indicates a mains or mains fuse fault (a flashing LED indicates a battery fault). From the ZP2 Series Installation Manual, Table 3 "Common…

The yellow Sounder Fault/Disabled/Test LED indicates a sounder fault, disablement, or test. A flashing LED indicates a fault; a steady LED indicates a disablement or a test. From the ZP2 Series Installation Manual,…

Yellow SYSTEM FAULT indicator, flashing: the manual says this LED is also illuminated if the write protect / write enable switch is left on while the system is not in the engineer menu. In access levels 1 and 2 a system…

Event message on the SIMPO addressable panel. The manual's Appendix A table describes it as: Circuit broken at Fault output. The manual gives no cause or action for this message.

The source names this fault message and gives only the applicable module/input numbering (x from 1 to 4); it states no cause, meaning, or remedy beyond that numbering. No cause is asserted here beyond what the source…

The manual says that when the 6100 detects a fault in any of the critical operating paths it shows it on the front panel display and the internal buzzer pulses slowly. The General Fault indicator is illuminated and is…

Per the manual, if the system detects a device fault or fire activation during initialisation, initialisation does not fail at that point. Beyond certain limits initialisation will fail and the various fault or fire…

Per the manual, if the panel detects a short circuit or leakage current to earth/screen from one of its supply rails (0 V or +Ve) an Earth Fault is displayed. The normal voltage between 0 V and Earth SCRN is 1.7 V; the…

Message shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: A fault with the auxiliary supply has been detected. Action listed in the manual: Check the auxiliary voltage and any associated wiring.

Message shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: A fault with the extinguishing system has been detected. Action listed in the manual: Check wiring to extinguishing system.

Message shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: A wiring fault has been detected to earth. Action listed in the manual: The fault can be narrowed down by systematically disconnecting…

Message shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: A fault with the loop booster has been detected. Action listed in the manual: Replace loop booster module.

Message shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: There is a problem with a loop device that has a fault monitored circuit such as a conventional detection zone. Action listed in the…

Message shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: This indicates a fault in the equipment connected to the third-party protocol RS232 port has been detected. Action listed in the…

Per the manual, a fault is indicated if any part of the system enters an abnormal condition. The COMMON FAULT LED pulses (and the ALARM FAULT/DISABLEMENT LED also pulses if the fault is with an alarm circuit), the…

With the Power Supply Fault LED pulsing, press and hold ENTER (fault diagnosis mode): the LED steady after pressing ENTER means battery failure or high impedance. The specification table (printed page 9) gives the…

No individual cause or remedy is stated beyond the message name; the source only states that the FPP-5000-TI13 Communication Interface transmits this fault to the panel. No cause is asserted here beyond what the source…

No individual cause or remedy is stated beyond the message name; the source only states that the FPP-5000-TI13 Communication Interface transmits this fault to the panel. No cause is asserted here beyond what the source…

No individual cause or remedy is stated beyond the message name; the source only states that the FPP-5000-TI13 Communication Interface transmits this fault to the panel. No cause is asserted here beyond what the source…

No individual cause or remedy is stated beyond the message name; the source only states that the FPP-5000-TI13 Communication Interface transmits this fault to the panel. No cause is asserted here beyond what the source…

No individual cause or remedy is stated beyond the message name; the source only states that the FPP-5000-TI13 Communication Interface transmits this fault to the panel. No cause is asserted here beyond what the source…

No individual cause or remedy is stated beyond the message name; the source only states that the FPP-5000-TI13 Communication Interface transmits this fault to the panel. No cause is asserted here beyond what the source…

No individual cause or remedy is stated beyond the message name; the source only states that the FPP-5000-TI13 Communication Interface transmits this fault to the panel. No cause is asserted here beyond what the source…

No individual cause or remedy is stated beyond the message name; the source only states that the FPP-5000-TI13 Communication Interface transmits this fault to the panel. No cause is asserted here beyond what the source…

No individual cause or remedy is stated beyond the message name; the source only states that the FPP-5000-TI13 Communication Interface transmits this fault to the panel. No cause is asserted here beyond what the source…

No individual cause or remedy is stated beyond the message name; the source only states that the FPP-5000-TI13 Communication Interface transmits this fault to the panel. No cause is asserted here beyond what the source…

Message shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: The impedance of the battery wiring is too high. Action listed in the manual: Check the battery wiring connections.

Message shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: Loop device has failed a self check. Action listed in the manual: Replace sensor.

Message shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: A specific loop device, when polled, is returning a very low analogue value. Action listed in the manual: Check the device for…