Fault records by panel

Circuit broken at input 'Alarm Confirmation'.

Short circuit detected at input 'Alarm Confirmation'.

Circuit broken at input 'Protection Alarm Confirmation'.

Short circuit detected at input 'Protection Alarm Confirmation'.

Per the manual, a sounder short circuit fault lights the Gen S/C LED. Check the correct end of line (10K resistor) has been fitted to both circuits; check that all sounders and bells are polarised and fitted the correct…

Per the manual, an earth fault indicates that something is shorting to earth, usually through the cable screen. Disconnect the earth screens one at a time to determine the problem line. Connecting other equipment, for…

The manual says most faults need checking by an engineer, but the system can be checked for a removed detector by the responsible person. All faults in the Premier Elite are non-latching: they cannot be reset with the…

Per the manual, for a sounder open circuit fault: check that the correct end-of-line resistor (10K) has been fitted to both circuits; check sounder fuses FS4 and FS5 are intact; check there are no breaks in the cable…

Per the manual, a power supply fault indicates loss of mains power or loss of battery power. For loss of mains: check that 230 V AC is present at the mains terminal block, check the mains fuse, check that there is 30 to…

Per the manual, a system fault is an abnormal microprocessor running condition due to various unexpected phenomena, and the panel attempts to correct itself. The System Fault LED, General Fault LED, General Fault relay…

Per the manual, an open circuit zone fault: check that the correct end-of-line diode (1N4002) has been fitted; check there are no breaks in the cable and all screw connections are secure; check no detectors have been…

Per the manual, a short circuit zone fault lights the Gen S/C LED. Check that the correct end of line (1N4002 diode) has been fitted and not backwards (stripe to +ve); check that no equipment other than detectors or…

Power supply status indicator on the Zeta Premier AL power supply board. The manual lists it as: 5 V supply low.

Power supply status indicator on the Zeta Premier AL power supply board. The manual lists it as: Battery fault.

Power supply status indicator on the Zeta Premier AL power supply board. The manual lists it as: Charger fault.

LCD event text on the Zeta Premier AL. The manual's Appendix D describes it as: Data Fault: the analogue value reported by the device is not valid.

LCD event text on the Zeta Premier AL. The manual's Appendix D describes it as: Double Address: two or more devices exist with the same address.

Power supply status indicator on the Zeta Premier AL power supply board. The manual lists it as: Earth fault, printed in the manual as “Earth fault (disabled)”; the diagram beside it shows the earth fault monitoring…

LCD event text on the Zeta Premier AL. The manual's Appendix D describes it as: Auxiliary power supply fuse failed.

Power supply status indicator on the Zeta Premier AL power supply board. The manual lists it as: Low battery voltage (below 19 V).

LCD event text on the Zeta Premier AL. The manual's Appendix D describes it as: Open circuit fault detected in the loop cable. This may be due to an operation of short circuit isolators.

Power supply status indicator on the Zeta Premier AL power supply board. The manual lists it as: Input from the SMPS out of tolerance.

Power supply status indicator on the Zeta Premier AL power supply board. The manual lists it as: P.S.E. processor fault.

Power supply status indicator on the Zeta Premier AL power supply board. The manual lists it as: Power supply healthy; the indicator switches off for 1 second every 30 seconds during the battery discharge test.

LCD event text on the Zeta Premier AL. The manual's Appendix D describes it as: Remote Fault at the address indicated.

LCD event text on the Zeta Premier AL. The manual's Appendix D describes it as: Removed: the loop device is not responding.

Per the manual, in the event of a complete system failure a system fault is indicated: the SYSTEM FAULT and GENERAL FAULT LEDs illuminate and all other LEDs are extinguished; the internal buzzer sounds continuously; the…

Per the manual, a fault is indicated if any part of the system enters an abnormal condition. The COMMON FAULT LED pulses (and the ALARM FAULT/DISABLEMENT LED also pulses if the fault is with an alarm circuit), the…

Power supply status indicator on the Zeta Premier AL power supply board. The manual lists it as: Thermistor fault.

LCD event text on the Zeta Premier AL. The manual's Appendix D describes it as: Wrong Type: the device at this address is different from that configured for the address.