Fault records by panel

From the panel's own "View - Panel" diagnostic table: each loop's load is monitored 0mA-500mA; the panel reports Open Circuit when the reading falls outside that range in the open direction. Loop Load, V.Out and V.In…

The loop current reading indicates an open-circuit state on the detection loop. From the official Advanced MxPro5 User Manual's Local Hardware diagnostic table (section 3.9.7.2, pp.22–23), which lists Open Circuit as…

Per the manual, if the system faces a loop +ve to -ve short circuit or a loop +ve open circuit during initialisation, initialisation fails at that point and a message of Loop not complete is displayed. Devices up to…

Per the manual, if random or recurrent loop open circuit faults are reported, check the entire system for: loose connections; broken connectors (over-tightening can break the connector body and cause an intermittent…

Per the manual, if short circuit or open circuit faults occur on the loop wiring the panel detects them and indicates them with the yellow loop fault LED and logs them in the event logs. Adjacent devices open their…

Per the manual, power is driven from the LOOP OUT terminals and returned to the LOOP IN terminals, where it is monitored for loop continuity. If the loop is open circuit (a cable fault, or a short circuit isolator…

Message shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: The loop wiring has a disconnection. Action listed in the manual: Check the loop wiring connections at the panel. If these are good and…

The loop has a break in its wiring. The fault threshold is set to 100Ω.

The ZFP loop driver reports Open Circuit when it detects an open circuit on the addressable loop.

The loop current reading indicates a short-circuit state on the detection loop. From the official Advanced MxPro5 User Manual's Local Hardware diagnostic table (section 3.9.7.2, pp.22–23), which lists this as one of the…

The CIE-A-400 has recorded an intermittent or recurrent open-circuit condition on an addressable loop.

The CIE-A-400 has identified an open circuit on the negative core of the indicated loop during initialisation.

Per the manual, if the system faces a loop -ve open circuit during initialisation, initialisation does not fail at that point but continues to the end of the loop and all devices are operational (as long as no other…

Per the manual, if the system faces a loop -ve open circuit during initialisation, initialisation continues to the end of the loop and all devices are operational (as long as no other faults exist). A message of…

Message shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: Open-circuit wiring fault detected on the loop or on-board monitored input circuit. Action listed in the manual: Check wiring. Check…

Message shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: Open-circuit wiring fault detected on an on-board sounder or monitored loop output device. Action listed in the manual: Check wiring.…

Per the manual, this engineering function momentarily asserts the LED outputs of loop devices in one continual sweep, and is useful for locating open or short circuit faults on the loop wiring. LEDs are asserted step by…

The loop current reading is above the normal operating range — an overload condition on the detection loop. From the official Advanced MxPro5 User Manual's Local Hardware diagnostic table (section 3.9.7.2, pp.22–23),…

Message shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: Loop isolator is open circuit either by command from the panel or because of a loop fault. Action listed in the manual: Check if device…

Message shown on the ID50/ID60 panel. The manual's Appendix 3 gives the meaning as: There is a problem with a loop device that has a fault monitored circuit such as a conventional detection zone. Action listed in the…

The manual says the panel's loop isolator monitors the addressable loop for open and short circuit faults, reported as ISOLATOR FAULTS with a description. For a break in the positive wire, it says to locate the cable…

Per the manual, if the system detects a device fault or fire activation during initialisation, initialisation does not fail at that point. Beyond certain limits initialisation will fail and the various fault or fire…

LCD event text on the Zeta Premier AL. The manual's Appendix D describes it as: Open circuit fault detected in the loop cable. This may be due to an operation of short circuit isolators.

Per the manual, in the event of a complete system failure a system fault is indicated: the SYSTEM FAULT and GENERAL FAULT LEDs illuminate and all other LEDs are extinguished; the internal buzzer sounds continuously; the…